AB PLC 1715系列IO 机架故障排除经验总结

工控安全 1年前 (2022) admin
511 0 0
AB PLC 1715系列IO 机架故障排除经验总结
JZGKCHINA
工控技术分享平台

中英文双语技术文章



Lesson Learn of AB PLC 1715 IO Rack Fault Status Troubleshooting 

AB PLC 1715系列IO 机架故障排除经验总结

系统背景

System Background 

Compressor control system network is a Ring network composed of a pair of redundant controllers, 2 IO racks and other devices. 

压缩机控制系统是由一对冗余控制器、两个IO机架以及其他设备构成的环形控制网络。

AB PLC 1715系列IO 机架故障排除经验总结

The communication link from the CPU to IO Rack is redundant. 

控制器与IO机架之间的通讯是冗余的。


问题陈述

Problem Statement

Rack-2 all the modules show abnormal status. 

2号机架所有模块状态异常。 

AB PLC 1715系列IO 机架故障排除经验总结

Re-power the Rack-2, modules could not resume work. 

重新上电状态不能恢复。 

AB PLC 1715系列IO 机架故障排除经验总结

调查发现

Findings

Ping Rack-2 IP Address (192.168.7.72) failed.

 2号机架IP地址(192.168.7.72)Ping 不通。 

AB PLC 1715系列IO 机架故障排除经验总结

RSlinx also could not recognize. 

使用RSlinx 同样识别不到该机架。 

AB PLC 1715系列IO 机架故障排除经验总结

采取措施

Action taken

Remove the first “AENTR” module to check the MAC address of the Rack-2. 

拆除机架最左侧第一块“AENTR”模块,查看机架MAC 地址。 

AB PLC 1715系列IO 机架故障排除经验总结

Laptop connects to network switch, and set the IP address in range of the control network. 

笔记本电脑链接至网络交换机,设置同网段IP地址。

Open the “BootP DHCP EtherNet/IP Commissioning Tool” software; the scan job will carry out automatically. 

打开“BootP DHCP EtherNet/IP Commissioning Tool”软件,自动搜索。 

AB PLC 1715系列IO 机架故障排除经验总结

Double-click the device (MAC address matching the Hardware label) to set an IP address.

 双击设备(与硬件标签相匹配的MAC地址)设定IP地址。 

AB PLC 1715系列IO 机架故障排除经验总结
AB PLC 1715系列IO 机架故障排除经验总结

Select the device from the menu below and hit the “Disable BOOTP/DHCP” button. 

在下方列表选中设定好IP地址的设备,然后点击“Disable BOOTP/DHCP”。 

AB PLC 1715系列IO 机架故障排除经验总结

Note注意:

This step is very important, after pressed, the message must be showed as“[Disable BOOTP] Command successful”

这一步非常重要,点击之后,一定要在下方信息栏看到“[Disable BOOTP] Command successful”命令发送成功的信息提示 

AB PLC 1715系列IO 机架故障排除经验总结

Otherwise, the IP address configuration will be lost in any powered down.

否则设备会在断电后丢失之前设定的IP地址。 

Sometimes, the message not come or receive a fault message, should try more times or change to use the other way to “Disable BOOTP/DHCP” as below:

有时,点击后会出现没有信息提示或者返回报错信息,这个时候就要多试几次,或者使用其他方式发送“Disable BOOTP/DHCP”命令,如下:

●  Select the device → Menu Bar → Tools →“Disable BOOTP/DHCP”

选择设备 → 菜单栏 → Tools →“Disable BOOTP/DHCP” 

AB PLC 1715系列IO 机架故障排除经验总结

Select the device → right click → “Disable BOOTP/DHCP”

选择设备 → 右键 →“Disable BOOTP/DHCP” 

AB PLC 1715系列IO 机架故障排除经验总结

处理结果

Result Status

Rack-2 status is back to normal. 

机架、模块状态恢复正常。 

AB PLC 1715系列IO 机架故障排除经验总结

作者简介



淡定齿轮:

常驻伊拉克油田现场的工控人
油气上游领域自动化过程控制从业多年

1.Smart200&V90伺服系统:已更新12课

2.贝加莱直播课程:已更新42课

3.工控三人行:已更新5课

4.剑指工控经典公开课:已更新22课
5.ABB运动控制:已更新6课
6.新品推荐:已更新15课

7.EPLAN快速入门:已更新2课

AB PLC 1715系列IO 机架故障排除经验总结

原文始发于微信公众号(剑指工控):AB PLC 1715系列IO 机架故障排除经验总结

版权声明:admin 发表于 2022年12月7日 上午6:01。
转载请注明:AB PLC 1715系列IO 机架故障排除经验总结 | CTF导航

相关文章

暂无评论

您必须登录才能参与评论!
立即登录
暂无评论...